Vintagehifi.dk

tctla skrev:Her er det lidt usikker ud-af-boxen tænkning, men jeg synes at huske, at netop det problem skyldes defekte gummibøsninger, indbygget i alle 4 fødder.
De hedder noget i stil med PEB-100 eller PEB-114 og kan måske stadig skaffes NOS.
Jeg kan spørge min leverandør...

cdp skrev:Har set et billede på nettet af modellen - det ser ud til arm/værk/tallerken er afkoblet fra plinten..
Har du kigget under tallerkenen ?? hvis den har db. afkobling, så mål lige "Water" hhv. på tallerken og plint.
- just in case...

Have you tried adjusting the feet?

There are several sources and solutions for new cushions or boots for the Pioneer PL-600. The springs and feet in this model are also used in a number of other decks. But the lower-level models like PL-400 and PL-5 use a different foot.

When searching for solutions, the PL-L1000 seems to be the most popular of the bunch. The boots are pioneer part PEB102. Many try some type of washer or o-ring instead of a full boot.

There are new solutions coming up all the time. For example, google produced these: https://www.etsy.com/listing/266683207/ ... -l1000-etc


There was also an ebay seller and Pioneer PL-L1000 'guru' Professor Bizzt from Florida. I think he's pretty much done using ebay but you might find him with some searches. He makes / made O-rings for the cushions.

And ebay seller Lasermel made boots in the past. Not sure what his status is at the moment.

I wouldn't recommend using the transport screws.
User avatar
Van_Isle long player
long playercontributor Posts: 1439Images: 33Joined: 23 Oct 2008 19:21Location: British Columbia
Canada

cdp skrev:Er det kun pladetallerkenen der hælder, - eller hele spillen..?(foto)
Edit - måske tager jeg fejl mht. opbygning Allan, på min Onkyo er der bøs med fjedre, der afkobler værk/arm.
Disse skulle også efterjusteres for at ophænget stod 'lige'. Derudover er der selve fødderne, som afkobler plinten.
Men som sagt, det kan sagtens være anderledes på din jo. - hvis du forsigtigt tager tallerkenen af, løfter den samtidig med modhold på akslen, så kan du sikkert lure systemet af og se hvor der er hængepartier, - hvis ikke Sound 2 V. allerede har justeret det op...Ps. motor må helst ikke få strøm uden tallerken.

Have you tried adjusting the feet?

There are several sources and solutions for new cushions or boots for the Pioneer PL-600. The springs and feet in this model are also used in a number of other decks. But the lower-level models like PL-400 and PL-5 use a different foot.

When searching for solutions, the PL-L1000 seems to be the most popular of the bunch. The boots are pioneer part PEB102. Many try some type of washer or o-ring instead of a full boot.

There are new solutions coming up all the time. For example, google produced these: https://www.etsy.com/listing/266683207/ ... -l1000-etc


There was also an ebay seller and Pioneer PL-L1000 'guru' Professor Bizzt from Florida. I think he's pretty much done using ebay but you might find him with some searches. He makes / made O-rings for the cushions.

And ebay seller Lasermel made boots in the past. Not sure what his status is at the moment.

I wouldn't recommend using the transport screws.
User avatar
Van_Isle long player
long playercontributor Posts: 1439Images: 33Joined: 23 Oct 2008 19:21Location: British Columbia
Canada

MaxJ skrev:Jeg har en service manual hvis det har interesse.

Allan. A skrev:Nå Lars fra sound2vision mener han kan skaffe nogle nye gummi skåle, så det satser jeg på i første omgang :)

cdp skrev:

Allan. A skrev:Nå Lars fra sound2vision mener han kan skaffe nogle nye gummi skåle, så det satser jeg på i første omgang :)

Super Allan - så er den ged jo barberet.. - og tillykke med spillen.